Roofing Contractor Serving Hillside, NJ

Hillside is a township of about 22,500 residents on under three square miles on the northern edge of Union County, bordered by Newark and Irvington in Essex County, Elizabeth to the east and southeast, and Union Township to the west. Lionel Trains operated a factory here from 1929 to 1974, and Bristol-Myers Squibb has had a presence in town. Conant Park, the township’s largest, is bounded by the Elizabeth River, and Evergreen Cemetery is the resting place of writers Stephen Crane and Mary Mapes Dodge. Hall of Fame shortstop Phil Rizzuto lived for decades in the Westminster neighborhood.

Monarch Roofing & Construction serves Hillside from our base at 168 Humboldt St in East Rutherford. We repair and replace pitched and flat roofs, repair chimneys and flashing, and replace gutters and siding.

Roofing in a Dense, Established Suburb

At more than 8,000 people per square mile, Hillside is closely built, with about 7,500 housing units as well as commercial properties. Common roofing needs here include the following.

Established homes

Homes that have been re-roofed more than once may carry multiple layers that hide damaged decking. Chimney flashing patched with tar, worn valleys, and flat roofs over porches and rear additions are frequent leak sources. A full tear-off at replacement lets us inspect and repair the deck.

Multi-family houses

For owners of rental properties, we coordinate access, protect tenants, and explain repair options clearly.

Commercial and industrial buildings

Flat and low-slope commercial roofs need sound seams, flashing at rooftop units and walls, and clear drainage. Ponding and blistering are early warning signs.

Close quarters

On smaller lots, we plan dumpster placement and protect neighboring homes during tear-off.

Roof Repair in Hillside

We replace damaged shingles, re-flash chimneys and walls, repair valleys and vent boots, and fix flat roof seams and drains. See our roof repair services.

Roof Replacement in Hillside

Pitched roof replacements include tear-off, deck repair, underlayment, leak barrier, drip edge, new flashing, and new roofing. Flat roof replacements include a new membrane with properly flashed walls and edges.

Chimney Repair and Flashing

We repoint mortar joints, repair or rebuild crowns, rebuild deteriorated chimneys above the roofline, and install new step and counter-flashing where the chimney meets the roof. See our chimney repair and flashing page.

Gutters and Siding

We replace gutters and downspouts, repair rotted fascia, and repair or install siding. Learn more about our gutter and siding services.

Choosing a Roofer

Ask for a written scope of work, ask whether any permit or approval applies, and ask how hidden deck damage will be priced. New Jersey generally requires home improvement contractors working on residential property to register with the Division of Consumer Affairs, and registrations can be verified online.

What Affects the Cost

Roof type and size, layers, flat sections, deck repairs, chimneys, materials, and access all affect price. Your free written estimate explains the scope.

Hillside Roofing FAQs

Do you have an office in Hillside?

Our nearest regional office is in Cresskill, and our main headquarters is at 168 Humboldt St, East Rutherford, NJ 07073.

Do you work on commercial buildings?

Yes. We repair and replace flat and low-slope commercial roofs.

Do I need a permit?

Usually not. Replacing the roof covering on a detached one- or two-family home is generally treated as ordinary maintenance under New Jersey’s Uniform Construction Code (N.J.A.C. 5:23-2.7), so a construction permit is usually not required. Structural work such as replacing rafters, attached homes, and historic-district or HOA rules can change that, so check with your municipal construction office or ask us during your free inspection.

How do I get an estimate?

Call or text (551) 241-0470, email monarchroofingnj@gmail.com, or use our estimate request form.

Nearby Areas

We also serve Newark, Irvington, Maplewood, Union, Elizabeth, and other communities in our service area.

Hillside, NJ Roofing Contractors: Our Regional Office and East Rutherford Headquarters

Monarch Roofing & Construction serves Hillside homeowners in the Westminster neighborhood, near Conant Park and the Elizabeth River, and along the Newark, Irvington, and Union borders. Our regional office is located at 488 12th St, Cresskill, NJ 07626, and our main headquarters is located at 168 Humboldt St, East Rutherford, NJ 07073.

Call or text (551) 241-0470, email monarchroofingnj@gmail.com, or book online.

Schedule a Roofing Appointment Online

Hillside homeowners can book a free roof inspection or free roofing estimate using the button below.

Hillside, NJ Roofing Questions Answered

Who provides roofing services in Hillside, NJ?

Monarch Roofing & Construction serves Hillside homeowners with roof repair, roof replacement, roof installation, roof leak repair, asphalt shingle roofing, chimney repair and chimney flashing, and siding. We serve the township from our regional office in Cresskill and our headquarters in East Rutherford. Our NJ Home Improvement Contractor registration is HIC #13VH12036000. Call or text (551) 241-0470.

Where can I find roof repair near me in Hillside?

Monarch Roofing & Construction provides residential roof repair throughout Hillside. Book a free inspection online or call or text (551) 241-0470, and we will explain what the repair involves.

Who offers free roof inspections in Hillside?

Monarch offers free roof inspections and free roofing estimates to Hillside homeowners. Book online or call or text.

How do I choose a reliable roofing contractor?

Check New Jersey Home Improvement Contractor registration through the state’s lookup, get a written scope of work with materials listed, and confirm whether any permit or approval applies. Ask for proof of insurance before work starts.

Should I repair or replace my roof?

A leak from tarred-over chimney flashing or a single worn valley is often a repair. Multiple layers, widespread wear, or recurring leaks usually point toward replacement with a full tear-off. A free inspection gives you a clear answer.

How much does roof replacement cost in Hillside?

Cost depends on roof size and pitch, the number of layers, decking repairs, flashing at chimneys and walls, ventilation, the shingle line, access on smaller lots, and any permit or approval fees that apply. A free written estimate gives the real number.

What are the signs of roof damage?

Look for curled or missing shingles, granules in gutters, rusty or tarred flashing, worn valleys, ceiling stains, and large icicles at the eaves in winter.

How can I schedule a roofing estimate?

Use the online scheduling button above, call or text (551) 241-0470, or email monarchroofingnj@gmail.com.

Honest Roof Assessments

Honest Roof Assessments. Clear Recommendations. Repairs When Possible. Replacement When Necessary. We inspect the whole roof, show you photos, and recommend a repair whenever it will solve the problem reliably.

  • Free roof inspections and free roofing estimates
  • NJ Home Improvement Contractor registration #13VH12036000
  • Itemized written estimates

Weather and Wear in Hillside

Hillside is closely built, with mature trees along many streets and parkland along the Elizabeth River. Trees fill gutters and valleys each fall and shade some slopes enough to grow moss. Homes near the river and park stay a bit damper, which makes attic ventilation important. Winters bring snow and dozens of freeze-thaw cycles that slowly open gaps at chimney mortar and flashing, and homes with warm attics develop ice dams. Summer thunderstorms bring gusty winds and heavy rain.

Why Tarred Flashing Is a Warning Sign

Many older roofs show thick black roofing cement smeared around chimneys, vent pipes, and wall joints. Tar is often applied as a quick fix when flashing starts to leak. It can slow water for a season or two, but it dries, cracks, and pulls away as the roof expands and contracts. Worse, it can hide rusted or missing metal underneath. When we see heavy tar, we look closely at what lies beneath and recommend proper replacement of the flashing rather than another layer of patching.

Residential Roof Inspections

  1. Shingle condition and number of layers.
  2. Chimney flashing, crown, and mortar.
  3. Step and kick-out flashing.
  4. Pipe boots and vents.
  5. Valleys and gutters.
  6. Attic ventilation, insulation, and moisture.

A Clear Estimate

For roof replacement in Hillside NJ, a clear estimate covers tear-off of all layers, decking repair terms, ice and water shield at eaves, valleys, and penetrations, synthetic underlayment, drip edge, new flashing, the shingle product, ventilation, protection of neighboring homes, and cleanup.

Leak Diagnosis and Storm Damage

Water usually enters at flashing, cracked vent boots, worn valleys, or missing shingles, then travels along framing before dripping. We trace it to the source. After a storm, photograph damage with the date, protect the interior, stay off the roof, and schedule an inspection. If you file an insurance claim, the insurer decides what is covered.

Flashing Details

  • Chimney flashing: step and counter-flashing, with a cricket on wider chimneys. We also repair and rebuild chimneys.
  • Pipe flashing: boots that seal plumbing vents.
  • Step flashing: layered with shingles where roofs meet walls.
  • Kick-out flashing: at the base of roof-to-wall joints.

Decking and Protective Layers

After tear-off, decking is inspected and damaged sections replaced. Ice and water shield goes at eaves, valleys, and penetrations; synthetic underlayment covers the rest; drip edge protects the perimeter.

Ventilation

Balanced soffit intake and ridge exhaust keeps attics drier and cooler, reducing ice dams and protecting shingles.

Gutters and Siding

We install gutters and siding along with roofs, helping manage water on close-set lots.

The Roof Replacement Process

  1. Free inspection and written estimate.
  2. Shingle selection and scheduling.
  3. Property and neighbor protection.
  4. Tear-off of all layers.
  5. Decking repair.
  6. Drip edge, ice and water shield, and underlayment.
  7. New flashing.
  8. Asphalt shingles, ridge caps, and ridge vent.
  9. Cleanup and nail sweep.
  10. Final walkthrough.

Asphalt Shingle Roofing

Architectural asphalt shingles are a durable, attractive choice for Hillside homes of all styles.

More Hillside Roofing Questions

What is your nearest location to Hillside?

Our regional office is in Cresskill, and our headquarters is in East Rutherford.

Is roofing tar a permanent fix?

No. Tar can slow a leak temporarily, but proper flashing replacement is the lasting repair.

Do you work with landlords?

Yes. We coordinate scheduling with owners of multi-family homes so tenants can be notified.

Learn about our roofing services, chimney services, and siding services, or view all locations. Nearby, see Union Township roofing, Elizabeth roofers, and Irvington roof repair.

More Roofing Guidance for Hillside Homeowners

Hillside’s established neighborhoods, multi-family houses, and parkland along the Elizabeth River raise practical roofing questions that go beyond the basics on this page. This section walks through older-home considerations, ice dam prevention, gutters and drip edge, shingle choices, documenting storm damage, a replacement day by day, comparing estimates, and a maintenance calendar.

Older Homes: Layers and Decking

Many Hillside homes have been reroofed more than once. When a new layer of shingles was installed over an old one, the roof gained weight, the decking underneath was hidden from view, and the original flashing was usually left in place and covered with roofing cement. When it is time to replace a roof like that, removing every layer down to the deck is generally the better approach. It allows each section of sheathing to be inspected, so any soft, rotted, or delaminated wood can be replaced before the new roof goes on. It also allows new flashing to be installed at chimneys, walls, and vents rather than patching old metal again. A clear estimate should explain how many layers will be removed and how decking repairs are priced if they turn out to be needed.

Ice Dam Prevention

Ice dams form when heat escaping from the living space warms the roof deck, melting snow from below. The meltwater runs down to the eave overhang, which stays cold because it sits outside the heated walls, and refreezes into a ridge of ice. More meltwater then backs up behind it and can find its way under shingles and into walls and ceilings. The most effective steps are sealing air leaks from the house into the attic, keeping insulation deep and even without blocking soffit vents, and balancing ventilation so outside air enters at the soffits and exits at the ridge. Ice and water shield installed along the eaves provides a backup barrier if an ice dam does form.

How Gutters and Drip Edge Work Together

Drip edge is the metal trim along the roof’s edges. At the eaves, it carries water off the shingles and into the gutter instead of letting it wick back onto the fascia board and the top of the wall. The underlayment and ice and water shield lap over the drip edge so water stays on the outside of the roof system. Gutters then need to be pitched toward downspouts, fastened securely enough to carry the weight of ice, and kept clear of leaves. On close-set Hillside lots, downspouts should discharge away from both your foundation and your neighbor’s. When a roof is replaced, it is a good time to make sure gutters line up with the new drip edge.

Shingle Choices and Wind Ratings

Architectural asphalt shingles are thicker and more dimensional than older three-tab shingles, and each line carries a wind rating that applies when it is installed to the manufacturer’s specifications. Those specifications include the number of nails per shingle, where the nails go, starter strips at the eaves and rakes, and how ridge caps are fastened. On shaded lots near Conant Park, algae-resistant shingles help limit dark streaks.

Documenting Storm Damage

After a strong storm, photograph each side of the roof from the ground, along with any shingles or debris in the yard and any interior stains. Note the date, time, and weather. Protect the interior from drips, stay off the roof, and schedule an inspection. If you file an insurance claim, the insurer decides what is covered.

A Replacement, Day by Day

Materials are delivered and staged, and the house and neighboring property are protected. Tear-off proceeds section by section down to the deck, damaged sheathing is replaced, and each section is dried in with drip edge, ice and water shield, and synthetic underlayment. New flashing goes in at chimneys, walls, and vents, followed by starter strips, shingles, ridge vent, and ridge caps. Finally, gutters are cleared and the yard and driveway are swept for nails.

Comparing Estimates Line by Line

Compare the number of layers removed, decking terms, ice and water shield coverage, underlayment, drip edge, new versus reused flashing, the shingle line and its wind rating, ventilation work, protection of neighboring homes, and cleanup.

A Maintenance Calendar

  • Spring: check for winter damage and clean gutters.
  • Summer: look at the roof after storms and keep attic vents clear.
  • Fall: clean gutters after leaf drop.
  • Winter: watch for icicles and ice ridges at the eaves.

More Hillside Roofing Questions

Why is a second layer of shingles a problem?

It adds weight, hides decking damage, and usually means old flashing was left in place.

Should new gutters be installed with a new roof?

If existing gutters are worn or do not line up with the new drip edge, replacing them together is often efficient.

What does a shingle wind rating mean?

It describes the wind speed a shingle is designed to resist when installed to the manufacturer’s instructions.

A Closer Look at Roofs in Hillside

Hillside is a closely built township of about 22,500 residents on under three square miles on the northern edge of Union County, bordered by Newark, Irvington, Elizabeth, and Union Township. Its roughly 7,500 housing units include established single-family homes and multi-family houses, from the Westminster neighborhood to the streets around Conant Park and the Elizabeth River. This section looks at what Hillside’s housing means for roof work, how to check your attic and insulation, how porches and rear additions should be flashed, how to manage gutter water on close lots, how shingle color affects heat, what estimate line items cover, seasonal warning signs, what to expect at an inspection, and insurance documentation.

Housing and What It Means for the Roof

Established single-family homes. Homes that have been reroofed more than once may carry multiple layers that hide damaged decking. Chimney flashing patched with tar and worn valleys are frequent leak sources. A full tear-off at replacement lets the deck be inspected and repaired and every flashing detail be replaced with new metal.

Multi-family houses. For owners of rental properties, a leak affects tenants and can travel from the top unit to the units below. These homes often have several plumbing vents and exhaust fans, each needing a sound boot or flashing, and replacement projects require coordination with tenants.

Homes near Conant Park and the river. Parkland along the Elizabeth River brings mature trees and damper air, which means more leaves in gutters and a greater chance of condensation in poorly ventilated attics.

Checking Your Attic and Insulation

If you can safely reach your attic, look with a flashlight for dark stains or water trails on the underside of the roof boards, especially around the chimney and vent pipes where tarred flashing often fails. Check that insulation covers the attic floor evenly and is not blocking the soffit vents. On cold mornings, frost on nail tips means moist air is reaching the roof deck; in summer, an extremely hot attic means it is not venting heat. In multi-family homes, confirm that each unit’s bathroom and kitchen fans vent outside.

Porches and Rear Additions

Where a porch roof or rear addition meets the main wall, the joint depends on step flashing woven into the shingles, siding or counter-flashing lapped over it, and kick-out flashing at the base to turn water into the gutter. When these pieces are missing or replaced with roofing cement, water runs behind siding and into the wall. Stains on porch ceilings, damp back rooms, and soft siding near the joint are common signs.

Gutter Water on Close Lots

Drip edge directs water from the shingles into the gutter, gutters must slope toward downspouts and be cleaned after leaf drop, and downspouts should discharge away from both your foundation and your neighbor’s. On lots where houses sit close together, extensions or careful downspout placement keep water out of narrow side yards and basements.

Shingle Color and Heat

Darker shingles absorb more summer heat, which can warm top floors over poorly ventilated attics. Lighter or reflective colors reduce heat gain, and darker colors can help snow clear faster on sunny winter days. Balanced ventilation has the larger effect on attic temperature.

Estimate Line Items, Explained

  • Tear-off and disposal: removing all layers, often two on established homes.
  • Decking repair: replacing damaged plywood or boards, usually priced per unit.
  • Ice and water shield: membrane at eaves, valleys, walls, and penetrations.
  • Underlayment and drip edge: synthetic layer and metal edge trim.
  • Flashing: new chimney, step, pipe, and kick-out flashing instead of tar patches.
  • Ventilation: ridge vent, soffit intake, and fan venting.
  • Shingles: shingle line, starter strips, and ridge caps.
  • Logistics and cleanup: dumpster placement on smaller lots, neighbor protection, and nail sweep.

Seasonal Warning Signs

  • Spring: new stains in top-floor rooms, shingles lost over winter.
  • Summer: hot upper floors, curling shingles on sunny slopes.
  • Fall: gutters overflowing with leaves.
  • Winter: icicles, ice on shaded eaves, frost in the attic.

What to Expect at an Inspection

A free inspection covers the shingles, every porch and addition joint, the chimney and its flashing, the gutters, and the attic when accessible. You receive photos and a plain explanation of the roof’s condition and priorities.

Insurance Documentation

After storm damage, take dated photos of the roof from the street, debris, and every interior stain, and note when tenants reported problems. Keep receipts for emergency work. An inspection report describes the damage. If you file a claim, your insurer decides what is covered.

More Questions From Hillside Homeowners

Why does my porch ceiling leak in heavy rain?

The joint where the porch roof meets the house relies on step and kick-out flashing; when they fail, water enters.

Can tar-patched flashing be replaced without a new roof?

Often, yes, if the shingles around it are in good condition.

Do I need a permit to replace my roof in Hillside?

Replacing the roof covering on a detached one- or two-family home is generally treated as ordinary maintenance under New Jersey’s construction code, so a permit is usually not required. Structural work such as replacing rafters, attached homes, and historic-district or HOA rules can change that, so check with your municipal construction office.

Do tenants need to leave during a replacement?

No. With advance notice and interior protection, tenants can usually stay home.

Request a Free Roofing Estimate in Hillside

Monarch Roofing & Construction
168 Humboldt St, East Rutherford, NJ 07073
Call or text: (551) 241-0470
Email: monarchroofingnj@gmail.com